How to Prepare a Glass Cut List for Accurate Fabrication

A glass fabrication cut list is the document that tells a fabricator exactly what to manufacture. It identifies every glass piece, its finished dimensions, material, thickness, edgework and required machining. A complete cut list reduces questions, improves quotation accuracy and helps prevent panels from being produced for the wrong opening or hardware configuration.
The cut list should communicate finished requirements rather than leaving the fabricator to interpret the design. Terms such as “standard glass,” “polish as needed” or “typical hole” do not provide enough information for precise production. Each piece should be understandable even when reviewed without the person who originally measured the project.
What Should a Glass Fabrication Cut List Include?
The required fields vary according to the project, but every piece should have a unique identifier and complete production specification. A commercial project may contain hundreds of lites, while a shower enclosure may have only two or three panels. The same documentation principles apply to both.
| Cut-list field | Information to provide |
|---|---|
| Piece mark | Unique identification for the glass panel |
| Quantity | Number of identical pieces required |
| Width | Confirmed finished width with unit of measurement |
| Height | Confirmed finished height with unit of measurement |
| Thickness | Nominal glass thickness |
| Glass type | Clear, low-iron, tinted, patterned or another product |
| Treatment | Annealed, heat-strengthened, tempered or laminated |
| Edgework | Seamed, polished, beveled or another specified finish |
| Holes | Diameter, quantity and centerline locations |
| Notches and cutouts | Size, location, radius and orientation |
| Coating or surface | Product, surface number and viewing orientation |
| Application | Storefront, shower, partition, railing or other use |
| Revision | Current drawing or cut-list revision identifier |
Use a Unique Mark for Every Glass Type
Each panel or group of identical panels should receive a unique piece mark. A mark such as G-101 can connect the cut list to a floor plan, elevation, shop drawing and installation opening. The same identifier should appear on packaging when the finished glass is delivered.
Do not reuse one mark for pieces that differ in edgework, hole locations or coating orientation. Panels may have the same width and height but still require separate production instructions. Unique marks help prevent visually similar pieces from being installed in the wrong location.
State Whether Dimensions Are Finished Glass Sizes
A cut list should clearly state whether the dimensions represent finished glass sizes or field openings. Fabricators should not be expected to guess framing deductions, panel overlaps or installation clearances. If deductions have already been applied, label the values as final fabrication dimensions.
When a fabricator is expected to calculate sizes from openings, provide the exact framing or hardware system and approved deduction method. Rough openings alone may not reveal the glazing-pocket depth, setting clearance or required bite. Daltex’s guide to glazing takeoffs explains why opening dimensions and glass fabrication sizes are not automatically the same.
Use a Consistent Dimension Order
Choose a standard dimension order and apply it throughout the document. Width by height is commonly used, but it should be stated in the header so the values cannot be reversed. Include inches, millimeters or another unit beside the column heading and avoid mixing measurement systems without a clear conversion.
Tall, narrow panels can expose dimension-order errors quickly, but nearly square pieces may reach production before the problem is noticed. Orientation notes such as “viewed from exterior” or “viewed from room side” provide another way to confirm how the panel is represented. The drawing and cut list should follow the same convention.
Identify the Glass Type and Treatment Separately
Glass type and treatment should occupy separate fields because they describe different characteristics. A panel may use clear, low-iron, bronze, gray, patterned or reflective glass and may then be annealed, heat-strengthened, tempered or laminated. Combining these details into an incomplete abbreviation can create confusion.
The application should also be provided when safety glazing may be required. Doors, sidelights, shower enclosures and other hazardous locations often require approved safety glass. Daltex’s guide to safety glass explains how tempered and laminated products differ.
Specify Edgework by Individual Edge
Do not write “polish edges” unless every edge receives the same finish. Identify the top, bottom, left and right edges, then state whether each edge is seamed, flat polished, beveled or left according to another approved requirement. This matters when some edges remain exposed and others sit inside framing or channels.
The installed orientation must remain consistent with the drawing. If the panel can be viewed from only one side, mark that side and label the edge positions accordingly. A simple edge diagram can communicate the instruction more reliably than a long written note.
Dimension Holes From a Defined Datum
Every hole should include its diameter and centerline location. Measure from two clearly labeled reference edges rather than from nearby holes or an undefined corner. For example, a handle hole may be located from the bottom finished edge and the closing-side finished edge.
The selected hardware template should control hole diameter, spacing and required edge distance. Do not copy dimensions from a visually similar hinge, handle or roller because the mounting preparation may differ. The complete hardware should be approved before the cut list is released.
Describe Notches and Cutouts Completely
A notch needs width, depth, location and any required corner radius. Larger cutouts may also require a separate detail drawing with an enlarged scale. The cut list should reference that detail by drawing number and revision.
Avoid describing a cutout only by its intended function, such as “hinge notch” or “outlet opening.” Different products use different shapes even when they perform the same job. A dimensioned profile or manufacturer template provides a production-ready instruction.
Show the Viewing Side and Orientation
Orientation becomes critical when glass has a coating, tint, pattern, frit, decorative surface or different edgework on each side. Mark the exterior, interior, room side or shower side and state the direction from which the drawing is viewed. Labels such as top, bottom, hinge side and handle side add further clarity.
Low-E, reflective and decorative products may require a specific surface position. The fabrication and insulated-glass makeup should identify the numbered surface where the coating belongs. Reversing a coated panel can alter appearance and performance.
Use Templates for Irregular Shapes
Curved, angled and irregular pieces may not be fully communicated through a basic table. A stable physical template can represent the finished perimeter more accurately, especially when existing walls or openings are uneven. The template should not be made from material that stretches, curls or changes shape during transportation.
Mark the template with the piece number, quantity, glass type, thickness, room side and finished edge requirements. Confirm whether the fabricator should manufacture to the exact template perimeter or apply a stated deduction. Daltex’s fabrication guide provides additional guidance for custom shapes and templates.
Include an Insulated Glass Makeup
An insulated glass unit requires more information than overall width and height. The cut list or schedule should identify each glass lite, individual thicknesses, cavity width, overall unit thickness, coating position, tint, spacer color, gas fill and any tempered or laminated components. The complete makeup should be repeated or connected to an approved type designation.
Different building elevations may require different solar-control products even when the unit dimensions are identical. Use separate type marks when coatings, tints or safety treatments change. This prevents one general description from being applied to every opening.
Control Revisions Carefully
Every cut list should display a revision number or date. When a measurement or fabrication detail changes, issue a new revision and identify what was modified. Old copies should be removed from active use so purchasing, fabrication and installation teams work from the same information.
Verbal changes create a significant documentation risk. An approved written revision provides a record that can be checked before production. For commercial projects, Daltex’s project support can coordinate takeoffs, shop drawings, submittals and fabrication information.
Review the Cut List Before Release
A final review should compare the cut list against field measurements, architectural drawings, hardware templates and project specifications. Quantities, dimension order, glass type, safety treatment and edgework should be checked for every piece. Coating orientation and insulated-glass makeup deserve separate verification because they may not be obvious after material is ordered.
The person releasing the glass should confirm that surrounding construction is ready for reliable measurement. The fabrication team can clarify available glass types, edge finishes and production requirements before an incomplete order reaches the shop. Early clarification is usually more efficient than correcting a released cut list.
Final Takeaway
An accurate glass fabrication cut list identifies every panel through a unique mark and provides finished dimensions, quantity, glass type, thickness, treatment, edgework, hardware preparation and orientation. Irregular shapes require clear drawings or stable templates, while coated and insulated products need complete makeup information. Revision control and a final cross-check help ensure that the fabricator, contractor and installer are working from the same approved requirements.
Frequently Asked Questions
1. Should a cut list show opening sizes or glass sizes?
A fabrication cut list should normally show finished glass sizes unless the fabricator has agreed to calculate deductions from documented openings. The dimension type should be clearly stated at the top of the list.
2. Should width or height be listed first?
Width by height is commonly used, but the chosen order must be labeled and applied consistently. The drawing orientation should follow the same convention to prevent dimensions from being reversed.
3. How should glass holes be dimensioned?
List the hole diameter and locate its centerline from two defined finished edges. Manufacturer hardware templates should control spacing, edge distance and cutout requirements.
4. Do polished edges need to be listed separately?
Yes, each top, bottom, left and right edge should receive a defined finish. This prevents concealed edges from being unnecessarily polished and ensures exposed edges receive the correct processing.
5. Can I submit a hand-drawn glass cut list?
A legible hand drawing may be sufficient for a simple piece when every dimension and fabrication detail is clear. Complex panels should use dimensioned drawings, hardware templates or stable physical templates.
6. When can the cut list be changed?
Changes should be made before material enters irreversible fabrication or heat treatment. Every change should receive a written revision so outdated dimensions are not used accidentally.